857d manual

DATA Jack. ACC Jack. KEY Jack. This transceiver covers an incredibly wide frequency range, over which a number of different operating modes are used. You can change the channel steps and operating mode once you get started, of course, per the next section. Start with the AF knob set fully counter-clockwise, especially when using FM the background noise on FM can be surprisingly loud!

A full discussion of the Menu system begins on page 94; for now, here is a brief. Press and hold in the [FUNC] key for one second to save the new setting and exit to normal operation. If you had previously pressed the [FUNC] key to enable the changing of the func-. In the U.

You will observe an increasing number of bars on the S-meter as you rotate the RF Gain control counter-clockwise; this indicates increasing AGC voltage, which is causing the front-end gain to be reduced.

Clockwise rotation of the DIAL increases the operating fre-. The SELECT knob provides faster tuning, ideal for making quick changes in frequency when you want to move across the band in a hurry. You can then use the DIAL knob to make fine frequency adjustments. See pages 97, , and for details. See page for details. However, a faster tuning rate may be selected, for quick navigation up and down the band. The operating mode will be preserved, along with the frequency information, on each VFO.

This facilitates split-band operation, such as on FM satellites. The FTD includes the capability for transmission and reception on the five spot frequencies assigned to the Amateur Service in the United States. To operate on the 5 MHz band:. The frequencies and operating mode for 5 MHz band operation are both fixed, and may not be changed. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Version Only Tone Search Scanning FTD Operating Manual 1. FTD Operating Manual 3. FTD Operating Manual 5. In mobile installations, it is preferable to mount your antenna on top of the roof of the vehicle, if feasible, so as to utilize the car body as a counterpoise for the antenna and raise the radiation pattern as far away from passengers as possible.

During vehicular operation when stopped in a parking lot, for example , make it a practice to switch to Low power if there are people walking nearby. Do not attempt to drive your vehicle while making a telephone call on an autopatch using the DTMF microphone. FTD Operating Manual 7. Route the DC cable as far away from the ignition cables as possible.

Caution Permanent damage can result if improper supply voltage, or reverse-polarity voltage, is applied to the FTD. MMB Installation. FTD Operating Manual 9. A good ground system can contribute to station efficiency in a number of ways: It can minimize the possibility of electrical shock to the operator.

FTD Operating Manual Important Note! Multi Function Keys These three keys select many of the most important operating features of the transceiver. The selec- tions available are The selections available are The selected function will appear above the [B] key. It is also used for inter-. KEY Jack This 3.

A full discussion of the Menu system begins on page 94; for now, here is a brief AF discussion on how to change Menu settings: 1. Clockwise rotation of the DIAL increases the operating fre- quency. To operate on the 5 MHz band: 1. If you have partitioned your memory channels into Memory. CH No. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add.

Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for. Register and get 5 for free.

Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need. Preliminary Inspection Installation Tips Safety Information Power connections Mobile Station Grounding Antenna Considerations Mobile Antenna Installations RF Field Exposure Electromagnetic Compatibility Heat and Ventilation Linear Amplifier Interfacing Adjusting the Front Feet Multi Function Key Detail Rear panel Connectors Turning the Transceiver On and Off Operating Band Selection Mode Selection Adjusting the Audio Volume Level Menu Quick Start Adjusting the RF Gain and Squelch Setting the Operating Frequency Changing the Dial Speed Stacked VFO System Receiver Accessories Locking Front Panel Controls IF Shift Noise Blanker Automatic Power-Off Feature Transmitter Operation There are memory channels available for storage and recall of important frequencies.

Normal Memory Storage 1. Tune in the desired frequency, and set the operating mode and bandwidth. This is easily accomplished using the Menu mode. When the Spectrum Scope Monitor is activated, the display indicates the relative signal strength on channels immediately adjacent to the current operating frequency.

Whether you are in the VFO mode or one of the memory modes, scanning operation is fundamentally identical in all configurations, but with the following differences: r In the VFO mode, scanning causes the transceiver to sweep up or down the band, paus- ing or halting on any signal encountered; Once the scan has been halted, one of three things may happen: TIME default action : In this mode, the transceiver pauses on the signal and stays locked on its frequency for five seconds.

Initiate memory scanning; you will observe that the channels you marked to be skipped are not included in the scanning loop. The PMS feature is especially useful in helping you to observe any operating sub-band limits which apply to your Amateur license class. A typical example might be for you to set VFO-A to Beacon Text Storage 1. To set up the Lamp mode: 1. Page 3. Repeat the previous step as many times as necessary to complete your callsign.

Up to 40 characters may be stored. The stor- age procedure is as follows: 1. Available Values: LPF: Lower frequencies are emphasized. HPF: Higher frequencies are emphasized. BOTH: Mid-range frequencies are emphasized. MOD: Indicates the deviation level. Available Values: 0. This allows multiple control operations to be fully automated as a single mouse click, or it allows a third-party software package such as contest logging software to communicate with the FT without redundant operator intervention.

The last byte in each block is the instruction opcode, while the first four bytes of each block are arguments either parameters for that instruction, or dummy values required to pad the block out to five bytes. To clone from one transceiver to another, use the following procedure: 1. The example below is designed around the popular satellite UO, but the same principles apply to operation using AO, and other such satellites.

A complete set of frequencies may be stored for each LEO satellite you wish to utilize, and once configured, the FT provides a flexible and easy-to-use earth station capability for these popular satellites. The MH adjust the operating frequency and receiver audio volume level. Empfang: 1 A Senden: 22 Sender 2. FTD Bedienungsanleitung 3. FTD Bedienungsanleitung 5. FTD Bedienungsanleitung 7.

FTD Bedienungsanleitung 9. FTD Bedienungsanleitung Wichtiger Hinweis! Diese Buchse wird auch zum. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.

Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need.

Technische Daten Tipps zur Aufstellung EMVU: Personenschutz Elektromagnetische Probleme Anschluss von Taste oder Keyer Anzeigen im Display Einund Ausschalten Wahl der Betriebsart Einstellen der Frequenz Verriegelung der Bedienelemente Clarifier RIT Senden in CW Senden in FM Manuelle Abstimmung Normales Speichern Aufrufen von Speichern Maskieren eines Speichers Bezeichnung von Speichern Dual Watch